Microstructural Characterization and Mechanical Properties of Rapidly Solidified Al-Si Systems by Chill Block Melt-Spinning Technique.

Authors

  • Amal Elsherif Mansoura University
  • Mustafa Kamal Mansoura University
  • Rizk Mostafa Shalaby Mansoura University

DOI:

https://doi.org/10.24297/jap.v17i.8607

Keywords:

Micro-Creep, AlـSi Alloys, Structure, Microstructure, Mechanical Properties, Micro Hardness Test, Electrical Resistivity

Abstract

AlـSi alloys with compositions (0, 0.1, 0.5, 0.9 and 1.3 wt.% Si) were manufactured by chill block melt spinning method. The resulting ribbons samples have been characterized by xـray diffraction (XRD) and scanning electron microscope (SEM). Detailed analysis of (XRD) shows that presence of f.c.c Al solid solution and Si particles embedded within the aluminum grains. Microstructural examination resulted that microstructure of the melt spun ribbons are more fine and uniformly distributed. Rapid solidification technology led to increase the solubility of Si in αـAl as confirmed by XRD. Micro hardness measurements were also carried out by Vickers microـhardness tester at applied load 25gm forced and different dwell time. It is concluded that the Vickers hardness values are sensitive to applied load and indentation time. It is also found that the highest values of Hv is sensitive to presence of Si as columnar shape with fine grained of Al by high cooling rate.

Downloads

Download data is not yet available.

Author Biographies

Amal Elsherif, Mansoura University

Metal Physics Laboratory, Physics Department, Faculty of Science, Mansoura, Egypt

Mustafa Kamal, Mansoura University

Metal Physics Laboratory, Physics Department, Faculty of Science, Mansoura, Egypt.

Rizk Mostafa Shalaby, Mansoura University

Metal Physics Laboratory, Physics Department, Faculty of Science, Mansoura, Egypt

References

S.P. Nikanorov, M.P. Volkov, V.N. Gurin, Y.A. Burenkov, L.I. Derkachenko, B.K. Kardashev, L.L. Regel, W.R. Wilcox, Structural and mechanical properties of Al-Si alloys obtained by fast cooling of a levitated melt, 390 (2005) 63–69.

J.A. Lee, Cast Aluminum alloy for high-temperature applications( A ) ( B ), 1 (2019)713-13.

W.R. Osório, N. Cheung, L.C. Peixoto, A. Garcia, Corrosion Resistance and Mechanical Properties of an Al 9wt % Si Alloy Treated by Laser Surface Remelting, 4 (2009) 820–831.

H. Kaya, M. Gu, H. Kaya, M. Gu, Dendritic Growth in an Aluminum-Silicon Alloy, 16 (2007) 12–21.

M.G. Kalhapure, P.M. Dighe, Impact of Silicon Content on Mechanical Properties of Aluminum Alloys, 4 (2015) 2013–2015.

F. Alshmri, Rapid Solidification Processing : Melt Spinning of Al-High Si Alloys, 390 (2012) 5–12.

B.V.S. Rao, A.C. Reddy, Fluidity of modified and unmodified Al-Si alloys in alumina investment shell moulds, Natl. Conf. Adv. Des. Approaches Prod. Technol. 4 (2005) 22–23.

S. Priyadarshini, S. Pattnaik, M.K. Sutar, Advancement in Property Improvement in Aluminium-Silicon Alloys : A Review, Int. J. Eng. Technol. Sci. Res. 4 (2017) 826–832.

L. Kloc, S. Spigarelli, E. Cerri, E. Evangelista, T. Langdon, An evaluation of the creep properties of two Al-Si alloys produced by rapid solidification processing, Metall. Mater. Trans. A. 27 (1996) 3871–3879.

O. Uzun, T. Karaaslan, M. Gogebakan, M. Keskin, Hardness and microstructural characteristics of rapidly solidified Al-8-16 wt.%Si alloys, J. Alloys Compd. 376 (2004) 149–157.

.L. Murray and A.J. McAlister, Bull. Alloy Phase Diagrams, 5.1, Feb.(1984)74-684.

T.J. Phys, Production and Structure of Rapidly Solidified Al-Si, J. Phys. 25 (2001) 455–466.

Yifan Sun,etal, ThermalandElectricalConductivityofLiquidAl–SiAlloys SpringerScience+BusinessMedia ,LLC,part of SpringerNature,40(2019)40-31.

Mustafa Kamal, AM Shaban, M El-Kady, Rizk Shalaby, Irradiation, mechanical and structural behaviour of Al-Zn-based alloys rapidly quenched from melt, Taylor & Francis Group (1996) 307-318.

M Kamal, AM Shaban, M El-Kady, RM Shalaby, Determination of structure-property of rapidly quenched aluminum-based bearing alloys before and after gamma irradiation , 2nd International Conference of Engineering Physics and Mathematics, Faculty of Engineering, Cairo University, Cairo (1994) 107-121.

H.H. Liebermann, The dependence of the Geometry of glassy alloy ribbons on the chill block melt-spinning process parameters, Mater. Sci. Eng. 43 (1980) 203–210.

B.D. Cullity, Elements of X-ray Diffraction, 2nd edition, Addison-Wesley, 1978, p. 248.

Rizk Mostafa Shalaby, T. El-Ashram, Effect of rapid solidification and small additions of Zn and Bi on the structure and properties of Sn-Cu eutectic alloy, J. Electron. Mater. 34 (2005) 212–215.

Rizk Mostafa Shalaby, Effect of indium content and rapid solidification on microhardness and micro-creep of Sn-Zn eutectic lead-free solder alloy, 432 (2010) 427–432.

G. Physics, L. Estv, Investigation of the superplasticity of tin-lead eutectic by impression creep tests, 21 (1986) 3287–3291.

B. Kucharska∗ and J. Kowalczyk, Resistance Properties of Al-Si Coatings. 129 (2016)18-23

Downloads

Published

2020-02-14

How to Cite

Elsherif, A., Kamal, M. ., & Shalaby, R. M. . (2020). Microstructural Characterization and Mechanical Properties of Rapidly Solidified Al-Si Systems by Chill Block Melt-Spinning Technique. JOURNAL OF ADVANCES IN PHYSICS, 17, 79–91. https://doi.org/10.24297/jap.v17i.8607

Issue

Section

Articles

Most read articles by the same author(s)

1 2 > >>